Axle Washers: Difference between revisions

Jump to navigation Jump to search
m
no edit summary
(Created page with "none|thumb|Mini-Logo Axle Washers Axle Washers (Also known as Axle Spacers, Speed Washers or Speed Rings) are small metal rings that y...")
 
mNo edit summary
Line 1: Line 1:
[[File:Mini-Logo Axle Washers.jpg|none|thumb|Mini-Logo Axle Washers]]
[[File:Mini-Logo Axle Washers.jpg|none|thumb|Mini-Logo Axle Washers]]


[[Axle Washers]] (Also known as Axle Spacers, Speed Washers or Speed Rings) are small metal rings that you slide onto your truck axles to encapsulate the wheel and bearings between the hanger and axle nut. These are meant to create a smoother ride and help prolong bearing life. You put one axle washer between the hanger and inside bearing, and another one between the outside bearing and the axle nut. This helps reduce friction, limit slop and keep your bearings from binding up. Without axle washers your bearings can end up rubbing against the truck hanger and axle nut.
[[Axle Washers]] (Also known as Axle Spacers, Speed Washers or Speed Rings) are small metal rings that you slide onto your truck axles to encapsulate the bearings between the hanger and axle nut. These are meant to create a smoother ride and help prolong bearing life. You put one axle washer between the hanger and inside bearing, and another one between the outside bearing and the axle nut. This helps reduce friction, limit slop and keep your bearings from binding up. Without axle washers your bearings can end up rubbing against the truck hanger and axle nut.


Freestylers also use axle washers to adjust axle depth and where the [[Wheels]] sit in relation to the edge of the [[Deck]]. By putting multiple axle washers behind the wheel, you can push your wheels outward, bringing the axle further inside the wheel (to avoid axle contact with the pavement), or to adjust the wheel-span for optimal rail alignment.  
Freestylers also use axle washers to adjust axle depth and where the [[Wheels]] sit in relation to the edge of the [[Deck]]. By putting multiple axle washers behind the wheel, you can push your wheels outward, bringing the axle further inside the wheel (to avoid axle contact with the pavement), or to adjust the wheel-span for optimal rail alignment.  


[[File:Axle Wheel Depth with 0 Axle Washers.jpg|none|thumb|This wheel has no axle washers installed on the inside bearing so the axle is almost flush with the outside of the wheel. We'll want to bring that in a bit.]]
[[File:Axle Wheel Depth with 0 Axle Washers.jpg|none|thumb|This wheel has no axle washers installed on the inside bearing so the axle is almost flush with the outside of the wheel. We'll want to bring that in a bit. ]]
{|
{|
|- style="vertical-align:top;"
|- style="vertical-align:top;"
|[[File:Axle Washers Used for Wheel Extension.jpg|none|thumb|2 axle washers were installed to bring the axle further into the wheel and extend the wheel out a bit further.]]
|[[File:Axle Washers Used for Wheel Extension.jpg|none|thumb|2 axle washers were installed to bring the axle further into the wheel and extend the wheel out a bit further.]]
||[[File:Axle Wheel Depth with 2 Axle Washers.jpg|none|thumb|This wheel now has 2 axle washers installed on the inside so there is now a good buffer between the axle and the outside edge of the wheel.]]
||[[File:Axle Wheel Depth with 2 Axle Washers.jpg|none|thumb|This wheel now has 2 axle washers installed on the inside so there is now a good buffer between the axle and the outside edge of this [[Momentum Kevin Harris M80 Freestyle Wheels|Momentum Kevin Harris M80 Freestyle Wheel]].]]
|}
|}


With regards to wheel-span, the wheels should never extend past the edge of the board. Placing the wheels even with the board will, however, help with [[Rail Whip]]s because it lessens deck drag. [[Bob Loftin]] recommends an optimal wheel-span somewhere around 1/8" to 1/4" narrower than the [[Deck]]. It is all a matter of preference, but this range can provide better rail stability. Just try some different settings and see which configuration works best for you.
With regards to wheel-span, the wheels should never extend past the edge of the board. Placing the wheels even with the board will, however, help with [[Rail Whip]]s because it lessens deck drag. [[Bob Loftin]] recommends an optimal wheel-span somewhere around 1/8" to 1/4" narrower than the [[Deck]]. It is all a matter of preference, but this range can provide better rail stability. Just try some different settings and see which configuration works best for you.
[[File:Wheel to Rail Measurement.jpg|none|thumb|This wheel is set back 1/16" from being flush with the rail, which sets the total wheel-span 1/8" narrower than the deck.]]
[[File:Wheel to Rail Measurement.jpg|none|thumb|This [[Seismic Focus 97A Wheels|Seismic Focus 97A Wheel]] is set back 1/16" from being flush with the rail of this [[Decomposed Per Canguru Caged Critter Deck]], which sets the total wheel-span 1/8" narrower than the deck.]]


[[Category:Glossary]]
[[Category:Glossary]]
[[Category:Skateboard Anatomy]]
[[Category:Skateboard Anatomy]]
Cookies help us deliver better freestyle-related content. By using our services, you agree to our use of cookies and promise to practice your footwork everyday.

Navigation menu